Without "full speed mode" activated, on PC's startup (power on), fans receive the set voltages which were in place on previous shutdown. What that mode does, is that it feeds full 12V to all fans for 3 seconds at PC's startup before returning set voltage levels to the ones they were on previous shutdown. On F6 RGB, long press on button #6 enables the "full speed mode". Don't some fans have quite high starting voltage? Like, 5V or so? Also, when selecting max speed mode on the 6th button, do you select a fan first by pressing the button and then enable max speed with button 6?Īlso, I don't mind if a fan is on all the time. The lights on the display seem a bit uneven. I can get the F6 Commander RGB here but it's a tiny bit pricey. 8w per channle do seem a bit low, though. X-Vision don't seem to be sold over here. Both are good fan controllers while in the end, i went with Sentry 3. When looking a fan controller for my Haswell build, i narrowed the selection down to NZXT Sentry 3 and Thermaltake Commander FT. What sets it apart is that you can link channels together and control linked channels at the same time. Downsides of it is that lowest fan speed is 40% and it only has 1x temp sensor. Oh, here's small tutorial of F6 RGB as well,Īs far as NZXT Sentry 3 goes, it looks very nice with it's vibrant colors and LED touchscreen. I've used my F6 RGB for over a year now and i can't tell that it feels flimsy or it's build quality is low. Then again F6 RGB is also one of the few who has 6x channels while most fan controllers have 5x or 4x channels. Since my local store didn't have black version of Bitfenix Recon available, only white version, i went with F6 RGB. Since i needed maximum control over my fans, my choice was either Thermaltake Commander F6 RGB or Bitfenix Recon ( specs). Most fan controllers go as low as 40% while the next step down from there is fan off. As seen here (German review),Īs far as Thermaltake Commander F6 RGB goes, it one of the few fan controllers out there that enables to control your fans with 0.1V steps, from 0.0V to 12.0V. Looking the fan controller at eye level and it's LED display seems dimmed out. Main reason why i got X-Vision for my AMD build is because it's display view angle is designed in a such way where your PC sits below your eye level. But yes, since it's a fan controller and not a fan hub, you can control all channels individually. Downside of this is that when you want to change e.g 3rd channel fan RPM, you need to go through the #1 and #2 channels first. With X-Vision, you first press "Set RPM" button, turn the knob to set RPM target and then press "Set RPM" button again, so that the fan controller would memorize the RPM. If you're interested, under the spoiler is a pic of my PCs and their fan controllers. Since i have NZXT HUE+ with it's LED strips in my build, i don't use Thermaltake Lumi LED strips with it. And if you don't have that many fans to connect to it, channel #5 and #6 also support Thermaltake Lumi series LED strips. Good side about F6 RGB is that it has 6x channels that support 3-pin and 4-pin fans. I too have Bitfenix Spectre Pro fans in use, 2x 140mm and my Aerocool X-Vision fan controller, in my AMD build (full specs with pics in my sig), controls both of my LED fans without any issue whatsoever.įor similar looking fan controller, you can go for Thermaltake Commander F6 RGB which i'm running in my Skylake build (also, full specs with pics in my sig) and which controls my Corsair ML140 Pro LED and NZXT AER140 RGB fans without issue as well. Plus their social media account seems to have died. Maybe I should send the controller back and get another one? Their website gives a lot of 404s and you can't contact them. The stock fan of the top of the case works perfectly well to control, though. In addition, the lamptron control seems to give off some kind of mild hum but not a low frequency one. I'm aware that the Lamptron control goes all the way down to 0 RPM. The LED lights don't use THAT much? Then I connect the Bitfenix fan back to the stock control again and it starts immediately and the LED lights too. With up to 20w per channel, power shouldn't a problem. And even at maximum it doesn't spin very fast. The second is that it doesn't start until I turn the knob to at least 75% of what's possible. I plug it in and one of the first things I notice is that it doesn't get any rpm data from the Bitfenix fan. Recently bought a fan controller (Lamptron FC6) because a pair of ports on the built-in one in my Corsair Graphite 600T case died.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |